Godbout Econoram X control settings

From: Jim Battle <frustum_at_pacbell.net>
Date: Mon May 20 00:51:51 2002

After my most recent round of Sol emulator enhancements, I'm finally
getting down to adding emulation for the Helios disk system.

Part of that effort is going to require me to get some binary disk images
in order to make the emulator do something useful.

Luckily, I happen to have a Sol stashed away along with a Helios disk
system. It was kindly donated to me last summer, but it has been in
storage waiting for me to have the time to rehabilitate it.

I bought a used varactor and ramped up the power on the Sol itself. No
caps blew, and it is now working just fine. At least, it plays TARG
OK. I've also replaced the key pads and it is now much a happier than it
was. I haven't tried messing with the helios system yet as it is going to
require a lot more work (dusting it out, cleaning things, sanity checking
it, praying like hell it doesn't need calibration after 20 years of idleness).

The system has two "Econoram by Godbout" boards, specifically "Econoram
X". Doing some probing of memory locations, it appears that only 48KB of
the available 64 KB of SRAM is enabled (each card has 64 4Kx1 SRAM
chips). 0x0000 to 0xBFFF is enabled, and the rest is disabled. Of course,
part of it must be disabled because 0xC000-0xCFFF is taken up by the
monitor ROM, display RAM, and scratch RAM. However, the higher parts
should be OK to use.

The dip switches on the boards have suggestive labels, but are too terse
for me to be confident what is going on.

Does anybody have docs on this or similar boards, or perhaps is better at
guessing what is going on than I am? I think I understand most of it, but
I'm sure I don't understand all of it.

First board's dip switch settings:

     S1:
     1: WE A = on
     2: WE B = on
     3: WE CL = on
     4: WE CH = on
     5: DIS A = off
     6: DIS B = off
     7: DIS C = off
     8: WS = off

     S2:
     1,2,3 = A = off, off, off
     4,5,6 = B = off, off, on
     7,8 = C = on, off


Second board's dip switch settings:

     S1:
     1: WE A = on
     2: WE B = on
     3: WE CL = on
     4: WE CH = on
     5: DIS A = on
     6: DIS B = on
     7: DIS C = off
     8: WS = off

     S2:
     1,2,3 = A = on, on, on
     4,5,6 = B = on, on, off
     7,8 = C = off, on

So it looks like the 32 KB on each board is broken up into three
banks. I'm guessing banks A and B control 8 KB blocks, and bank C is a 16
KB block (since S2 has three switches for A and B but bank C has only two
switches). WE A/B/C is write enable for each bank, and DIS A/B/C is
read&write enable/disable for each of the three banks. Perhaps WS is to
enable a wait state.

Sounds good so far, so let's collect the bank settings:

0 0 0 A1 = 0- 7, enabled
0 0 1 B1 = 8-15, enabled
1 0 C1 = 32-47, enabled

1 1 1 A2 = 56-63, disabled
1 1 0 B2 = 48-55, disabled
0 1 C2 = 16-31, enabled

Does this sound reasonable? At least it is consistent with my interpretation.

Does anybody know for sure what WS stands for?

One disturbing thing is that the I would have expected one board to
implement 0-31KB, and the other board to be used to map 32-47KB. Instead,
one board does 0-15 and 32-47, while the other board does 16-31. Any idea
why this might be?

Finally, does anybody know if this board respects phantom disable (some
other resource can claim a block of addresses and the board will silently
just map out that RAM location)?

Thanks.

-----
Jim Battle == frustum_at_pacbell.net
Received on Mon May 20 2002 - 00:51:51 BST