Another question....
I have an RK05 pack that has not been mounted since 1978. What are the
chances that it can still be read?
Ashley
----- Original Message -----
From: "Tom Uban" <uban_at_ubanproductions.com>
To: "General Discussion: On-Topic and Off-Topic Posts"
<cctalk_at_classiccmp.org>; "General Discussion: On-Topic and Off-Topic Posts"
<cctalk_at_classiccmp.org>
Sent: Wednesday, May 05, 2004 3:31 PM
Subject: Re: DEC RL01/02, RK05/06/07 Cartridge Inspector/Cleaner
> At 03:22 PM 5/5/2004 -0400, Ashley Carder wrote:
>
> >Does anyone here currently have a functioning RK05 drive?
> >Has anyone here ever brought one back from the dead?
>
> Yes, I have one which I brought back from the dead by replacing
> the foam, NiCd batteries, debugging the boards, etc.
>
> --tom
>
>
>
> >Ashley
> >
> >----- Original Message -----
> >From: "Tom Uban" <uban_at_ubanproductions.com>
> >To: "General Discussion: On-Topic and Off-Topic Posts"
> ><cctalk_at_classiccmp.org>; "General Discussion: On-Topic and Off-Topic
Posts"
> ><cctalk_at_classiccmp.org>
> >Sent: Wednesday, May 05, 2004 3:16 PM
> >Subject: Re: DEC RL01/02, RK05/06/07 Cartridge Inspector/Cleaner
> >
> >
> > > At 03:06 PM 5/5/2004 -0400, Ashley Carder wrote:
> > >
> > > >Does anyone know anything about this "Inspector / Cleaner"?
> > >
> > > The inspector cleaner allows you to hold the raw platter and to
> > > examine and clean it safely.
> > >
> > > >I've also seen mention of an "alignment pack" for RK05 drives.
> > > >Does anyone here have experience maintaining / aligning RK05 drives
and
> > > >keeping them running?
> > >
> > > In order to properly align an RK05 you need an alignment pack
> > > which has special "data" written at special locations. That
> > > together with a two channel o-scope, the manual and a few basic
> > > tools will allow you to adjust the in/out position of each head.
> > >
> > > The biggest problems with maintaining RK05s is that the foam
> > > which is used at various locations in the drive, including in
> > > the air path, disintegrates and turns to dust and/or goo. If
> > > you carefully clean out all of the old foam/dust/goo, you can
> > > fairly easily replace it with new foam purchased from a fabric
> > > store (or similar). A more difficult problem is that the molded
> > > plastic/rubber tube which ducts the air into the disk area also
> > > disintegrates over time. I haven't had to come up with a solution
> > > for this problem yet...
> > >
> > > --tom
> > >
> > > >Ashley
> > > >
> > > >----- Original Message -----
> > > >From: "Joe R." <rigdonj_at_cfl.rr.com>
> > > >To: <cctalk_at_classiccmp.org>
> > > >Sent: Wednesday, May 05, 2004 11:34 AM
> > > >Subject: DEC RL01/02, RK05/06/07 Cartridge Inspector/Cleaner
> > > >
> > > >
> > > > > Any of you that are interested in the old DEC disk drive systems
> >should
> > > > > take a look at this
> > > > > <http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=4129402394>
> > > > >
> > > > > Joe
> > >
>
Received on Wed May 05 2004 - 14:33:48 BST